Skip to content
jbilanderPublic

About

Spitfire 2000, A low-end 42 MHz Accelerator with IDE and 4/8 MB fast RAM for the Amiga 2000 co-pro slot (or A500 through an adapter).

Resources

Stars

33 stars

Watchers

6 watching

Forks

Repository files navigation

SF2000

Spitfire 2000, A low-end 42 MHz Amiga Accelerator based on the Motorola 68SEC000 CPU


This is WORK IN PROGRESS, a DIY hobby project. If you are going to make and sell boards you are also the one doing the customer support.

Revision 3A is brand new and has not been tested yet.

IMPORTANT Please do not build Revision 2B. We have found problems with the bus isolation on that revision which cause SRAM corruption. The Rev. 2B and Rev. 1B bills of material further down are kept for reference only.


The firmware for this board is in a separate repository available here:
https://github.com/jbilander/SF2000-FW


Revision 3A

Full schematic: SF2000_rev3a_schematic.pdf


Revision 1B


***

BOM Rev. 3A

Rev. 3A replaces the four asynchronous SRAMs with a single SDRAM, swaps the Efinix Trion for an Intel/Altera MAX 10, drops the on-board IDE interface, and adds an ESP32-C5 module and an RP2354A. Values and packages below are taken straight from the KiCad netlist.

Designator Name/Value Package Notes
U1 Voltage Regulator 3.3V,
LM1117-3.3 or
AMS1117-3.3
SOT-223 3.3V 1A Low Drop-Out (LDO) Linear Voltage Regulator, main 3V3 rail
LM111733QDCYRQ1 is the automotive-qualified LM1117-3.3 in SOT-223-4; any ordinary LM1117-3.3 in SOT-223 does the same job, and AMS1117-3.3 from AliExpress is a cheap alternative
U2 Voltage Regulator 4.3V, ABLIC S-1132B43-M5T1U or TPS73643DBVR SOT-23-5 4.3V LDO, the 4V3 supply rail for the CBT FET bus switches U4,U5,U6
S-1132B43-M5T1U
U3 Voltage Regulator 3.3V, TLV75533PDBVR SOT-23-5 3.3V 500mA LDO, separate 3V3_C5 rail for the ESP32-C5 module so its Wi-Fi bursts stay off the FPGA rail
TLV75533PDBVR
U4,U5 Digital Bus Switch 24-Bit FET, SN74CBT16211CDGGR or SN74CBT16811CDGGR TSSOP-56 FET level-shifter, Amiga +5V bus <-> 3V3
SN74CBT16211CDGGR (Mouser's own part number drops the trailing R, but it is the cut-tape CDGGR)
U6 Digital Bus Switch 10-Bit FET, SN74CBT3244PW TSSOP-20 FET level-shifter for the remaining control lines
SN74CBT3244PW
U7 Bus Transceiver 16-Bit, SN74LVC16245ADGGR TSSOP-48 Buffers the D0-D15 data bus, direction and output-enable driven by the FPGA (DATA_DIR, OE_D_HIGH, OE_D_LOW)
SN74LVC16245ADGGR
U8 Intel/Altera MAX 10 FPGA, 10M04SCU324C8G BGA-324, 15x15mm, 0.8mm pitch 4000 LE, internal configuration flash and UFM. It has to be the S single-supply variant - there is no 1.2V core rail on this board. The symbol and footprint in KiCad are drawn as a 10M02 so the design can be downsized to a 10M02SCU324 later if it fits; the firmware is developed for the 10M04
10M04SCU324C8G / 10M02SCU324C8G
U9 W25Q16JVSNIQ 16 Mbit SPI NOR Flash memory SOIC-8_3.9x4.9mm_P1.27mm (150-mil Narrow JEDEC SOIC) W25Q16JVSNIQ or AT25SF161B-SSHD-T
U10 Motorola CPU MC68SEC000AA20 20MHz QFP-64_14x14mm_Pitch0.8mm MC68SEC000AA20
U11 SDRAM 8Mx16 (128 Mbit),
IM1216SDBABG-6I or
AS4C8M16SA-6BINTR
TFBGA-54, 8x8mm, 0.8mm pitch Replaces the four SRAMs of Rev. 2B. 128 Mbit is 16 MB, which is the whole address space the MC68SEC000 can reach, so there is nothing to gain from a bigger part. The footprint is routed for all 13 address lines, so a 256 Mbit 16Mx16 part (AS4C16M16SA-6BIN) drops straight in as well should a large shadow RAM ever want one - unlikely, but the option costs nothing. On the 128 Mbit parts ball F9 (A12) is a no-connect, so the controller's row-address width has to match whichever density is fitted. On the Alliance part the -6BINTR suffix is cut tape and -6BIN is the tray version of the same device, which costs noticeably more
IM1216SDBABG-6I / AS4C8M16SA-6BINTR
U12 74HCT2G14GV,125 Dual Schmitt Trigger Inverter TSOP-6 / SOT457 / SC-74 Drives the SD_LED header J9 and the /SD_ACTIVE pin J10 at +5V
74HCT2G14GV,125
U13 ESP32-C5-WROOM-1U-N8R8 Module, 18 x 25.5mm, U.FL antenna connector The -1U variant uses an external antenna, so no PCB antenna keep-out is needed under or beside the module. If you fit the PCB-antenna -1 variant instead, the module has to be moved so its antenna end hangs over the board edge
ESP32-C5-WROOM-1U-N8R8 / ESP32-C5-WROOM-1-N8R8
U14 Level shifter 74LVC8T245PW,118 TSSOP-24 Clockport data bus CP_D0-CP_D7. 3V3 on the A side, +5V on the B side, direction and enable from the FPGA
74LVC8T245PW,118
U15 Level shifter 74LVC8T245PW,118 TSSOP-24 Clockport address and control (CP_A2-CP_A5, /CS, /IORD, /IOWR). +5V on the A side, 3V3 on the B side, DIR and /OE tied low so it always drives 3V3 -> +5V
74LVC8T245PW,118
U16 Raspberry Pi RP2354A QFN-60, 7x7mm, 0.4mm pitch MCU with 2 MB stacked flash. SPI slave to the FPGA (SS_RP2354, IRQ_RP2354) plus a UART link to the ESP32-C5
RP2354A (SC1511-A4)
U17 74LVC1G57GV Configurable Multiple-Function Gate TSOP-6 / SOT457 / SC-88A Wired as XNOR with A and B tied together: CLK7M = CCK XNOR CCKQ (replaces the SN74LVC2G86DCUR XOR of Rev. 2B). This is how the 7 MHz is generated on every supported machine - the real 7M is not present on the co-pro slot of the early German A2000, nor on A500 Rev 3 and Rev 5, but CCK and CCKQ always are
74LVC1G57GV,125
J1 Goldfingers on PCB, 86-pin ENIG Order PCB with Goldfingers, ENIG and 45 degrees chamfered edge (or chamfer the edge yourself with a file)
J2 CFGIN-header, Two-Pin Header 2.54mm (1 x 2) Put a jumper shunt here to activate autoconfig, or a CONFIGOUT-wire from another device into pin 2. Pin 2 is pulled up to +5V by R21
J3 JTAG-header Dual row 2.54mm (2 x 5) Pin Male Header
J4 JP-header JP2, JP3 2.54mm (2 x 2) Pin Male Header JP2 = Generate E-CLK (if the internal 68k is removed from the socket), JP3 = MapROM
J5 SWD pads, SWCLK / GND / SWDIO 2.54mm (1 x 3) Serial Wire Debug for U16 (RP2354A)
J6 ESP32 UART0, TX0 / RX0 2.54mm (1 x 2) Pin Male Header Console and flashing header for U13
J7 VCC/GND Two-Pin Header 2.54mm (2 x 1) VIN +5V
used when programming the FPGA standalone (card not installed in the Amiga). Be careful with orientation, check polarity BEFORE plugging-in a phone charger or similar here
J8 GCT MEM2055-00-190-01-A Micro SD Card Socket 9-pin push-pull micro-SD socket Wired for 4-bit SDIO as well as 1-bit SPI: SD_CS=DAT3, SD_MOSI=CMD, SD_MISO=DAT0, SD_D1=DAT1, SD_D2=DAT2
J9 SD_LED header, Two-Pin Header 2.54mm (2 x 1) Driven by U12 inverter buffer when /SD_CS is being asserted. Connect here to drive an external HDD-LED
J10 SD_ACTIVE low signal, Right angle Single-Pin Header 0.64 mm square pin angled Driven by U12 inverter buffer when /SD_CS is being asserted. Connect from here to a LED-board (Active low +5V-signal)
J11 RP2354A UART0, TX0 / RX0 2.54mm (1 x 2) Pin Male Header Console header for U16
J12 CLOCKPORT-header 2.00mm 22-Pin (2x11) Pin Male Header Caution: This header is +5V levels. Be careful with orientation
J13 JP-header JP1 2.54mm (2 x 1) Pin Male Header 7 MHz / Turbo selector
J14 USB-C Receptacle USB 2.0, HRO TYPE-C-31-M-12 16-pin SMD Native USB for the ESP32-C5 (U13)
J15 SPI-header: CS0, PROG_DET, SCK, MISO, MOSI, GND 2.54mm (1 x 6) Pin Male Header External SPI access to U9. PROG_DET tells the FPGA that a programmer is attached so it releases the bus
J16 USB-C Receptacle USB 2.0, HRO TYPE-C-31-M-12 16-pin SMD Native USB for the RP2354A (U16), UF2 / BOOTSEL
S1 4-way DIP switch, TDB04H0SB1R SMD, 1.27mm pitch Autoconfig fast-RAM size, RAMSZ0-RAMSZ3. Pulled up by RN1, so all switches OFF, or the switch not fitted at all, means 8 MB
X1 Crystal Oscillator 20 MHz Oscillator 5.0 x 3.2mm, 4-pad Do not populate. Every internal clock is derived from the 7 MHz reconstructed by U17, through the FPGA PLL. X1 is kept in the design in case a free-running clock is needed later; it lands on a dedicated clock input (CLK0p) through R3. Leave the pads empty until then
Y1 Crystal 12 MHz, ABM8-272-T3 3.2 x 2.5mm, 4-pad CL = 10 pF, +/-30 ppm. With C49/C50 = 15 pF and R12 = 1k this is the RP2350/RP2354 reference oscillator circuit
ABM8-272-T3
L1 Inductor 3.3uH, AOTA AB201610S3R3101T 2.0 x 1.6mm SMD shielded power inductor Switching inductor for the RP2354A internal core buck regulator (VREG_LX)
BT1,BT2 Tactile push button 3 x 4 x 2mm SMD, 2-pin BT1 = BOOT (pulls BOOTSEL low through R13), BT2 = RESET (pulls RUN low) for U16
BT3,BT4 Tactile push button 3 x 4 x 2mm SMD, 2-pin BT3 = BOOT (IO28 strap), BT4 = EN/RESET for U13
R1 22 Ω Resistor 0603 Series damping on CLK_SDRAM, straight off the FPGA PLL output pin
R2 33 Ω Resistor 0603 Series damping on the 7 MHz generated by U17, into the FPGA clock input
R3 33 Ω Resistor 0603 Series damping on OSC_CLK from X1 (only relevant if X1 is fitted)
R4 33 Ω Resistor 0603 Series damping on CLKCPU from the FPGA to U10
R5 33 Ω Resistor 0603 Series damping on SPI MOSI
R6 33 Ω Resistor 0603 Series damping on SPI SCLK
R7 33 Ω Resistor 0603 Series damping on SD_CLK to the micro SD card
R8 33 Ω Resistor 0603 RC filter into the RP2354A VREG_AVDD analog supply, together with C9
R9,R10 27 Ω Resistor 0603 USB series resistors for D+ / D- on J16
R11 330 Ω Resistor 0603 Series resistor for the SD_LED header J9, adjust to your LED and preferred brightness
R12 1k Ω Resistor 0603 Series resistor on XOUT of Y1 (RP2354A reference circuit)
R13 1k Ω Resistor 0603 Series resistor between BOOTSEL and the BOOT button BT1
R14 4.7k Ω Resistor 0603 Pull-up for RUN on U16, with C44 as the reset delay
R15,R16 5.1k Ω Resistor 0603 USB-C CC1 / CC2 pull-downs for J16
R17,R18 5.1k Ω Resistor 0603 USB-C CC1 / CC2 pull-downs for J14
R19 10k Ω Resistor 0603 Pull-up for JTAG TDI to 3V3
R20 10k Ω Resistor 0603 Pull-down for JTAG TCK
R21 10k Ω Resistor 0603 Pull-up for /CFGIN to +5V (J2 pin 2)
R22 10k Ω Resistor 0603 Pull-up for ESP32_RTS
R23 10k Ω Resistor 0603 Pull-down for PROG_DET
R24 10k Ω Resistor 0603 Pull-up for the ESP32-C5 EN pin, forms an RC reset delay with C46
R25 10k Ω Resistor 0603 Pull-up for CP_D_OE on the 3V3 side
R26,R27 10k Ω Resistor 0603 Pull-ups for JP2 and JP3
RN1 Resistor pack 10k Ω (CAY16-103J4LF) 1206 Pull-ups for RAMSZ0-RAMSZ3 (S1)
CAY16-103J4LF
RN2 Resistor pack 10k Ω (CAY16-103J4LF) 1206 Pull-ups for JP1, TMS, CONF_DONE and nSTATUS
RN3 Resistor pack 10k Ω (CAY16-103J4LF) 1206 Pull-ups for ESP32_CTS, nCONFIG, SD_D2 and SD_CS
RN4 Resistor pack 10k Ω (CAY16-103J4LF) 1206 Pull-ups for SD_CD, SD_D1, SD_MISO and SD_MOSI
RN5 Resistor pack 10k Ω (CAY16-103J4LF) 1206 Pull-ups for CP_IOWR, CP_IORD, CP_CS (3V3 side) and SS_W25Q16
RN6 Resistor pack 10k Ω (CAY16-103J4LF) 1206 Pull-ups to +5V for RST, CP_RTC_CS, CP_RTC_DS and CP_INT6 on the clockport
C1 Polarized Electrolytic Capacitor 100uF CP_Elec_6.3x7.7 mm Wurth SMD WCAP-AS5H 100uF
C2 Polarized Electrolytic Capacitor 22uF CP_Elec_5x5.8 mm Wurth SMD WCAP-AS5H 22uF
C3-C8 Ceramic Capacitor 10uF 1206 Bulk on the 3V3, 4V3, 3V3_C5 and clockport +5V rails
C9-C11 Ceramic Capacitor 4.7uF 1206 RP2354A supplies and core buck output
C12 Ceramic Capacitor 0.47uF = 470nF 1206
C13 Ceramic Capacitor 0.22uF = 220nF 1206 Local reservoir at the ESP32-C5 3V3 pin
C14-C19 Ceramic Capacitor 0.1uF = 100nF 0805
C20-C46 Ceramic Capacitor 0.1uF = 100nF 0603 Decoupling
C47,C48 Ceramic Capacitor 0.01uF = 10nF 0603
C49,C50 Ceramic Capacitor 15pF 0603 Load capacitors for Y1
C51-C72 Ceramic Capacitor 0.1uF = 100nF 0402 The cluster on the underside directly beneath U8 and U11

Rev. 3A board layout

Four layer stackup. The top and bottom layers carry the signal routing with a GND pour filling the gaps, the second layer is a solid GND plane and the third layer is a 3.3V plane.
Top layer, and the GND plane on inner layer 1:

The 3.3V plane on inner layer 2, and the bottom layer:


BOM Rev. 2B

Designator Name/Value Package Notes
U1 Voltage Regulator 3.3V,
LM1117-3.3 or
AMS1117-3.3
SOT-223 3.3V 1A Low Drop-Out (LDO) Linear Voltage regulator
U2 Voltage Regulator 4.3V, ABLIC S-1132B43-M5T1U or TPS73643DBVR SOT-23-5 4.3V LDO Linear Voltage Regulator
S-1132B43-M5T1U
U3 Voltage Regulator 1.2V, TLV73312PDBVR SOT-23-5 1.2V LDO Linear Voltage Regulator
TLV73312PDBVR
U4,U5,U6 Digital Bus Switch ICs 24-Bit FET, SN74CBT16211CDGGR or SN74CBT16811CDGGR TSSOP-56 FET Level-shifter
SN74CBT16211CDGGR or
SN74CBT16811CDGGR
U7 Dual XOR gate SN74LVC2G86DCUR VSSOP-8_2.3x2mm_P0.5mm Generates 7 MHz CLK from ~(CCK XOR CCKQ)
SN74LVC2G86DCUR
U8 Efinix Trion T8 FPGA T8Q144C3 LQFP-144_20x20mm_P0.5mm FPGA - Field Programmable Gate Array, 7384 LE, 97 I/O
T8Q144C3
U9 W25Q16JVSNIQ 16 Mbit SPI NOR Flash memory SOIC-8_3.9x4.9mm_P1.27mm (150-mil Narrow JEDEC SOIC) W25Q16JVSNIQ or AT25SF161B-SSHD-T
U10 Motorola CPU MC68SEC000AA20 20MHz QFP-64_14x14mm_Pitch0.8mm MC68SEC000AA20
U11 SST39LF802C-55-4C-EKE or SST39LF800A-55-4C-EKE TSOP-I-48_18.4x12mm_P0.5mm NOR Flash 3.0 to 3.6V 8Mbit Multi-Purpose Flash (for Kickstart)
S39LF802C554CEKE
S39LF800A554CEKE
U12 74AHCT14PW, Six Channel Schmitt Trigger Inverter TSSOP-14_4.4x5mm_P0.65mm 74AHCT14PW,118 or
SN74AHCT14PWR
U13 NOR Flash SST39LF040-55-4C-NHE-T PLCC-32 NOR Flash 3.0 to 3.6V
SST39LF040554CN
(or 39LF020, 39LF010)
U14,U15 SRAM ISSI IS61WV20488FBLL-10TLI TSOP-44 First 4 MB SRAM
High-Speed, Async, 2Mbx8, 10ns, 2.4v-3.6v, 44 Pin TSOP II, RoHS
IS61WV20488FBLL-10TLI
U16,U17 SRAM ISSI IS61WV20488FBLL-10TLI TSOP-44 Second 4 MB (Optional) --"--
J1 Goldfingers on PCB ENIG Order PCB with Goldfingers, ENIG and 45 degrees chamfered edge (or chamfer the edge yourself with a file)
J2 CFGIN-header Two-Pin Header 2.54mm pitch Put a Jumper shunt here to activate autoconfig, or a CONFIGOUT-wire from other device to the right (pin 2) in this header.
J3 JTAG-header Dual row 2.54mm (2 x 5) Pin Male Header
J4 JP-header JP2 2.00mm (2 x 1) Pin Male Header Generate E-CLK (if internal 68k is removed from socket)
J5 JP-header JP3 2.00mm (2 x 1) Pin Male Header Rom overlay jumper
J6 JP-header JP4 2.00mm (2 x 1) Pin Male Header 4/8 MB SRAM Config
J7 VCC/GND Two-Pin Header 2.54mm pitch VIN +5V
used when programming FPGA standalone (card not installed in the Amiga). Be careful with orientation, check polarity BEFORE plugging-in a phone charger or similar here.
J8 Sunrom Micro SD Card Holder 9-pin Micro SD card slot connector Sunrom Micro-SD card holder
J9 SD_LED header, Two-Pin Header 2.54mm pitch Driven by U12 inverter buffer when /SD_CS is being asserted. Connect to here in order to drive an external HDD-LED
J10 SD_ACTIVE low signal, Right angle Single-Pin Header 0.64 mm square pin angled Driven by U12 inverter buffer when /SD_CS is being asserted. Connect to here in order to drive a LED-board (Active low +5V-signal)
J11 Rom-bank selector 2.00mm (2 x 1) Pin Male Header Select first or second bank, address line A15 (pin 3) on U13 (SST39LF040)
J12 CLOCKPORT-header 2.00mm 22-Pin (2x11) Pin Male Header Caution: This header is +5V levels. Be careful with orientation.
J13 JP-header JP1 2.54mm (2 x 1) Pin Male Header 7 MHz / Turbo selector
X1 Crystal Oscillator 20 MHz Oscillator_7.0x5.0mm
R1 33 Ω Resistor 0805 Damping resistor for 20 MHz clock-signal coming from X1 oscillator
R2 33 Ω Resistor 0805 Damping resistor for 7 MHz clock-signal coming from U7 (SN74LVC2G86DCUR)
R3 33 Ω Resistor 0805 Damping resistor for CLKCPU clock-signal coming from FPGA pin 33
R4 ~220 Ω Resistor 0805 Series resistor for SD_LED header J9, adjust R-value to your type of LED and preferred brightness
R5 10k Ω Resistor 0805 Pull-up resistor for /FLASH_OE to 3V3
R6 10k Ω Resistor 0805 Pull-up resistor for JP2 to 3V3
R7 10k Ω Resistor 0805 Pull-up resistor for /CFGIN to 5V
R8 100k Ω Resistor 0805 Pull-up resistor for CRESET_N to 3V3
RN1-RN6 Resistor pack 10k Ω (CAY16-103J4LF) 1206 CAY16-103J4LF
C1 Polarized Electrolytic Capacitor 100uF CP_Elec_6.3x7.7 mm Wurth SMD WCAP-AS5H 100uF
C2 Polarized Electrolytic Capacitor 22uF CP_Elec_5x5.8 mm Wurth SMD WCAP-AS5H 22uF
C3-C7 Ceramic Capacitor 10uF 1206
C8 Ceramic Capacitor 2.2uF 1206
C9 Ceramic Capacitor 0.47uF = 470 nF 1206
C10-C39 Ceramic Capacitor 0.1uF = 100nF 0805
C40-C54 Capacitor 0.01uF = 10nF 0805

BOM Rev. 1B

Designator Name/Value Package Notes
U1 Voltage Regulator 3.3V,
LM1117-3.3 or
AMS1117-3.3
SOT-223 3.3V 1A Low Drop-Out (LDO) Voltage regulator. https://www.aliexpress.com/item/32869037691.html
U2 Voltage Regulator 4.3V, TPS73643DBVR or
ABLIC S-1200B43-M5T1U or
MIC5205YM5-TR ADJ (with R1,R2 and C7 populated)
SOT-23-5 4.3V LDO Voltage Regulator
* TPS73643DBVR
* S-1132B43-M5T1U
* MIC5205YM5-TR (Adjustable, populate R1,R2,C7)
U3 Inverter Schmitt Trigger 74LVC2G14GV,125 TSOP-6/SOT457/SC-74 * LVC2G14GV125
U4,U5,U6 Digital Bus Switch ICs 24-Bit FET, SN74CBT16211ADGGR TSSOP-56 FET Level-shifter
* SN74CBT16211ADGGR
* SN74CBT16811CDGG
U7 XNOR gate w/ Schmitt Trigger SN74AUP1T87DCKR TSSOP-5/SC-70-5/SOT-353-1 Generates 7 MHz CLK from CCK XNOR CCKQ
* SN74AUP1T87DCKR
U8 Gowin FPGA GW1N-UV9LQ144C6/I5 LQFP-144 FPGA - Field Programmable Gate Array, 8640 LE, 120 I/O
* GW1N-UV9LQ144C6/I5
U9 Motorola CPU MC68SEC000AA20 QFP-64 MPU 32-bit 20MHz
Contact Eriond to buy a NOS CPU for a reasonable price
U10,U11 SRAM ISSI IS61WV20488FBLL-10TLI TSOP-44 First 4 MB SRAM
High-Speed, Async, 2Mbx8, 10ns, 2.4v-3.6v, 44 Pin TSOP II, RoHS
* 61W20488FBLL10TI
U12,U13 SRAM ISSI IS61WV20488FBLL-10TLI TSOP-44 Second 4 MB (Optional) --"--
U14 NOR Flash SST39LF040-55-4C-NHE-T PLCC-32 NOR Flash 3.0 to 3.6V (For Oktagon/Oktapus. IDE-driver)
* SST39LF040554CN
(or 39LF020, 39LF010)
U15 SST39LF802C-55-4C-EKE TSOP-48 NOR Flash 3.0 to 3.6V 8Mbit Multi-Purpose Flash (for Kickstart)
* S39LF802C554CEKE
U16,U17,U18 Bus Transceiver 74LVC245APW,118 TSSOP-20 * 74LVC245APW-T
J1 Goldfingers on PCB ENIG Order PCB with Goldfingers, ENIG and 45 degrees chamfered edge (or chamfer the edge yourself)
J2 JTAG-header Dual row 2.54mm (2 x 5) Pin Male Header Strip
J3 JP-header JP2,JP3,JP4 Dual row 2.00mm (2 x 3) Pin Male Header Strip Turbo speed selector
J4 JP-header JP5 2.00mm (2 x 1) Pin Male Header Generate E-CLK (if internal 68k is removed from socket)
J5 IDE/ATA-header 2.00mm 44-Pin (2x22 Pin) Straight Male Shrouded PCB Box header IDC Socket For A2000:
* Shrouded header
For A500 internal mount a right angled female header can be used (2x25 and cut down to 2x22):
* Right Angle Female Connector
J6 Sunrom Micro SD Card Holder 9-pin Micro SD card slot connector * Sunrom Micro-SD card holder
J7 VCC/GND Two-Pin Header 2.54mm pitch 2.54mm pitch VIN +5V
used when programming FPGA standalone (card not installed in the Amiga). Be careful with orientation, check polarity BEFORE plugging-in a phone charger or similar here.
J8 JP-header JP6 2.00mm (2 x 1) Pin Male Header 4/8 MB SRAM Config
J9,J10 JP-header JP7,JP8 2.00mm (2 x 2) Pin Male Header JP7 Autoboot IDE OFF/ON Selector, JP8 Oktagon/Oktapus. IDE-driver Selector
J11 LED Two-Pin Header 2.54mm pitch 2.54mm pitch Driven by U3 inverter buffer when /Active on IDE is being asserted. Connect to here to drive an external HDD-LED
J12 /Active signal, Single-Pin Header 2.54mm 2.54mm pitch /Active signal from IDE. Connect from here to a
* LED-board
J13 Pmod Type 2A (SPI) Female header, 12-Pin (2x6) 2.54mm pitch For connecting SPI peripherals.
* Right-Angled (A2000) or
* Straight (A500) to not interfere with RGBtoHDMI-adapter inside A500
R1 1.2k Ω Resistor 0805 Feedback resistor, Only populate if U2 is of ADJ-ustable type (e.g. MIC5205YM5-TR)
R2 3k Ω Resistor 0805 Feedback resistor, Only populate if U2 is of ADJ-ustable type (e.g. MIC5205YM5-TR)
R3 10k Ω Resistor 0805 Pull-up resistor for /CFGIN (5V-side)
R4 10k Ω Resistor 0805 Pull-up resistor in RC-debounce circuit
R5 10k Ω Resistor 0805 Series resistor in RC-debounce circuit
R6 ~220 Ω Resistor 0805, 200 mW Series resistor for IDE-LED header J11, adjust R-value to your type of LED and preferred brightness
R7 1k Ω Resistor 0805 Pull-down resistor for IDE_IRQ
R8 4.7k Ω Resistor 0805 Pull-up resistor for IDE_IORDY
R9 10k Ω Resistor 0805 Pull-up resistor for JP6
R10 1k Ω Resistor 0805 Pull-down resistor for MODE0 (Gowin FPGA boot/configure from embFlash)
R11 1k Ω Resistor 0805 Pull-down resistor for MODE1 (Gowin FPGA boot/configure from embFlash)
R12 10k Ω Resistor 0805 Pull-up resistor for RECONFIG_N (Gowin FPGA) and /SPI_CS (in J13 Pmod-header)
R13 10k Ω Resistor 0805 Pull-up resistor for /ACTIVE (IDE)
RN1-RN2,RN5 Resistor pack 10k Ω (CAY16-103J4LF) 1206 * CAY16-103J4LF Pull-up resistors.
RN3-RN4 Resistor pack 10k Ω (CAY16-103J4LF) or 4.7k (CAY16-4701F4LF) 1206 * CAY16-4701F4LF Pull-up resistors for SD0-SD3,SD_CD,SD_CMD,JP7,JP8
C1-C2 Capacitor 10uF 1206
C3 Capacitor 0.1uF = 100nF 0805
C4 Polarized Capacitor 100uF CP_Elec_6.3x7.7 * Wurth SMD WCAP-AS5H 100uF
C5 Polarized Capacitor 22uF CP_Elec_5x5.8 * Wurth SMD WCAP-AS5H 22uF
C6 Capacitor 10uF to 0.22uF 1206 Check datasheet for U2 what is suitable here.
C7 Capacitor 0.33uF = 330nF 1206 (Not needed if U2 is TPS73643DBVR, check your U2-datasheet)
C8 Capacitor 10uF 1206
C9-C25 Capacitor 0.1uF = 100nF 0805 C24 capacitor in RC-debounce circuit
C26-C27 Capacitor 10uF 1206
C28-C46 Capacitor 0.01uF = 10nF 0805

A SF2000 shared shopping cart with most of the stuff in the list, no 3V3-regulator though and not all birdseed (passives): https://www.mouser.com/ProjectManager/ProjectDetail.aspx?AccessID=fdb374e26b


The FPGA used in this Accelerator board, please note it has to be the Voltage UV version because of 3.3V is being used for all VCC/VCCIO on the Accelerator:


Ordering details (JLCPCB):


*** ### MC68SEC000

The SF2000 is based on the MC68SEC000 CPU
https://www.nxp.com/docs/en/product-brief/MC68SEC000.pdf

You can contact Eriond, https://github.com/eriond (over at A314 or Retro Tinkering or SUGA (Swedish User Group Amiga) discord) to buy a NOS MC68SEC000 at a reasonable price.


Installing in A500 or A2000:

Internal A500 installation with this adapter:
https://github.com/jbilander/A500_Edge_Expansion_adapter


External A500 installation with this adapter:
https://github.com/jbilander/POC86


A2000 Co-pro slot:

***

Building

Follow the dots to get the correct orientation of the chips when soldering, don't rely on the silkscreen text.

You can solder the 3V3 LDO and the FPGA first and then check that you can communicate via JTAG programming a simple LED-blink example or similar. +5V you can take from a USB phone-charger or similar, check polarity before you plug it in.

Make sure you populate the 4V3 LDO like this if you are using TPS73643DBVR or ABLIC S-1200B43-M5T1U, populating R1,R2,C7 is only for a ADJ-regulator to achieve 4V3.


For A2000 and ribbon cable use you can solder a 44 pin IDE-header like this:


Performance

Some MC68SEC000 can be overclocked to 42 MHz and running with only one wait state for the IDE/ATA interface we can reach really good performance:

Flashing a ROM (in this case 3.1.4) to the FlashROM chip U15 (using LIV2's excellent sfflash-tool) and closing JP9 even better performance can be achieved:

Demo video:
https://drive.google.com/file/d/1dCBK24LUC5VLB2dshrW_5n82D2emHB5-/view?usp=sharing




But for running more stable a few wait states can be added to the IDE/ATA,
https://github.com/jbilander/SF2000-FW/blob/main/rtl/ata.v#L56
resulting in a bit slower IDE:



JTAG-header description:


Happy Hackin'


CC BY-SA 4.0

This work is licensed under a Creative Commons Attribution-ShareAlike 4.0 International License.

CC BY-SA 4.0

About

Spitfire 2000, A low-end 42 MHz Accelerator with IDE and 4/8 MB fast RAM for the Amiga 2000 co-pro slot (or A500 through an adapter).

Resources

Stars

33 stars

Watchers

6 watching

Forks

Releases

Packages

Contributors