A custom flipper-inspired multi-tool device - built from scratch.
I designed and built this project during Hackclub's Forge program - project link, to learn more about Embedded electronics, Radio frequency & Infrared communication & soldering, and hardware assembly.

BOM •
1 •
2 •
3 •
4
- Powered by an ESP32-S3 N16R8 microcontroller
- Built in Infrared & Sub-GHz modules
- WiFi 2.4 GHz and Bluetooth LE 5.0 capabilities
- Custom designed PCB & 3D Printed Case
- Simple menu UI on a 0.96" OLED display
- Can emulate Rubber Ducky payloads via bluetooth
- Supports microSD for efficient file management
- Rechargable 3.7V LiPo battery system (2000mAh)
- ESP-NOW communication protocol & messaging

| Component |
Type |
Price (£) |
Price ($) |
Link |
Notes |
| ESP32-S3 N16R8 |
Microcontroller |
£5.77 |
$7.79 |
AE |
ESP32-S3 N16R8 |
| SSD1306 0.96" OLED |
Display |
£1.36 |
$1.83 |
AE |
White 1pcs |
| IR Transceiver TXRX |
Infrared |
£0.94 |
$1.26 |
AE |
IR TxRx Kit |
| CC1101 Transceiver |
Sub-GHz |
£2.62 |
$3.52 |
AE |
Type-C3 |
| MicroSD Card Reader |
Storage |
£0.56 |
$0.75 |
AE |
TF SPI |
| MicroSDHC Card |
Storage |
£9.99 |
$13.41 |
Amazon |
16GB Performance Plus |
| 5D Nav Button |
Controls |
£0.76 |
$1.02 |
AE |
25mm x 20mm |
| 3.7V LiPo Battery |
Power |
£8.07 |
$10.84 |
AE |
1pcs (2000mAh) |
| TP4056 LiPo charger |
Power |
£0.14 |
$0.19 |
AE |
Type-C 1pcs |
| DD0403MB 3.3V LDO Module |
Power |
£2.21 |
$2.97 |
AE |
Output 3V3 No Pin |
| SS-12D00G 5mm switch |
Power |
£0.76 |
$1.02 |
AE |
20pcs SS-12D00G 5mm |
| Jumper Wires (Dupont) |
Electronics |
£3.30 |
$4.43 |
AE |
20cm M-M F-M F-F |
| Custom PCB |
Electronics |
£ |
$ |
JLCPCB |
(+ shipping) |
| 3D Print Case Filament |
Reimbursement |
£ |
$ |
HCB |
Rounded to 250g? |
| 5D Button Case Print |
3D Print File |
N/A |
N/A |
Makerworld |
Or make my own? |
| Total |
All |
£36.48 |
$49.03 |
BOM |
Rest of funds used for upgrades |
| Component Pin |
Net / Connection |
Notes |
| Battery + |
CH_+ (TP4056 B+) |
Raw battery input |
| Battery – |
GND / CH_- |
Shared ground |
| TP4056 CH_+ |
Battery + |
Charger input |
| TP4056 CH_- |
Battery – / GND |
Charger ground |
| TP4056 OUT+ (Pin 3) |
CHG_OUT |
Charger output to switch |
| TP4056 OUT– |
GND |
Same ground net |
| SW_SPDT Pin 1 |
CHG_OUT |
From TP4056 OUT+ |
| SW_SPDT Pin 2 |
LDO VCC |
Power to LDO (middle pin) |
| SW_SPDT Pin 3 |
NC |
Not used |
| LDO VCC |
SW_SPDT Pin 2 |
Input to regulator |
| LDO GND |
GND |
Regulator ground |
| LDO VO |
+3V3 |
Regulated 3.3V output |
| ESP32 3V3 |
+3V3 |
Main board power |
| ESP32 GND |
GND |
Common ground |
| Component Pin |
ESP32 Pin / Net |
Notes |
| VCC |
+3V3 |
Power |
| GND |
GND |
Ground |
| SDA |
GPIO8 (SDA) |
I2C data |
| SCL |
GPIO9 (SCL) |
I2C clock |
| Component Pin |
ESP32 Pin / Net |
Notes |
| VCC / +3V3 |
+3V3 |
Power |
| GND |
GND |
Ground |
| DAT |
GPIO4 (IR_TX) |
IR LED drive |
| Component Pin |
ESP32 Pin / Net |
Notes |
| VCC |
+3V3 |
Power |
| GND |
GND |
Ground |
| OUT |
GPIO5 (IR_RX) |
IR receive signal |
| Component Pin |
ESP32 Pin / Net |
Notes |
| VCC |
+3V3 |
Power |
| GND |
GND |
Ground |
| MOSI |
GPIO35 (SPI_MOSI) |
Shared SPI |
| MISO |
GPIO37 (SPI_MISO) |
Shared SPI |
| SCK |
GPIO36 (SPI_SCK) |
Shared SPI |
| CS |
GPIO38 (SD_CS) |
SD chip select |
| Component Pin |
ESP32 Pin / Net |
Notes |
| VCC |
+3V3 |
Power |
| GND |
GND |
Ground |
| MOSI |
SPI_MOSI |
Shared with SD |
| MISO |
SPI_MISO |
Shared with SD |
| SCK |
SPI_SCK |
Shared with SD |
| CSN |
GPIO41 (CC_CSN) |
Radio chip select |
| GDO0 |
GPIO39 (CC_GDO0) |
Interrupt pin |
| GDO2 |
GPIO40 (CC_GDO2) |
Interrupt pin |
| Nav Pin |
ESP32 Pin / Net |
Notes |
| F |
GPIO10 (NAV_F) |
Up |
| B |
GPIO11 (NAV_B) |
Down |
| L |
GPIO12 (NAV_L) |
Left |
| R |
GPIO13 (NAV_R) |
Right |
| M |
GPIO14 (NAV_M) |
Middle press |
| GND |
GND |
Common ground |
| Component Pin |
Net / Connection |
Notes |
| ESP32 RST |
NC |
No reset button used |
| 5V_IN |
NC |
Not used |
Designed and built by @gethin101